Bond It Silicone Ultra Waterseal - 5L

Name: Bond It Silicone Ultra Waterseal - 5L
Brand: Bond it
SKU: q3cpzomfbh
Availability: InStock

A premium grade solvent-free silicone water repellent for external masonry surfaces. Bond It ULTRA...

Best current price£20.64from eBay

Best offers

Shopping.co.uk recommended and popular offers

Lowest price

eBay£20.64Visit shop

Bond It 5L Silicone Ultra Waterseal Brick & Masonry Water Repellent Seal Render

Visit shop

Most popularTrusted

B&Q£23.49Visit shop

B&Q - 5L Silicone Ultra Waterseal Brick & Masonry Water Repellent Seal Render

Visit shop

All Offers

4 offers from £20.64 - £23.49

View price history by clicking the chart icon.

eBayBond It 5L Silicone Ultra Waterseal Brick & Masonry Water Repellent Seal Render

Free delivery in 1–3 days

£20.64

Visit shop

OnBuy.comBondit Bond It Silicone Ultra Waterseal - Clear 5L

Free delivery in 1–3 days

£20.88

Visit shop

B&QB&Q - 5L Silicone Ultra Waterseal Brick & Masonry Water Repellent Seal Render

Free delivery in 1–3 days

£23.49

Visit shop

Product Information

Full details

This guide is for homeowners and contractors looking to protect masonry surfaces from water damage. Bond It ULTRA WATERSEAL offers superior water repellency, preventing water ingress while allowing vapor to escape, leading to drier, warmer walls and reduced heating costs. Note that the product requires proper surface preparation for optimal performance.

All features

Model Part Number	BDH120
Brand	Bond it

Extended Product Information

FAQs

What surfaces can I apply Bond It ULTRA WATERSEAL to?

It is suitable for brick, stone, concrete, and unglazed tiles.

How long does it take for the product to dry?

The drying time will depend on the weather conditions. Ensure the surface is fully cured before exposure to heavy rain or water.

How many coats are required?

Two coats are recommended for optimal protection.

What is the coverage rate?

Approximately 3m² per litre for porous stone and 5m² per litre for hard brick.

Can I apply it in any weather?

Avoid applying in the rain. Protect the surface until it is fully cured.

Is Bond It ULTRA WATERSEAL environmentally friendly?

Yes, it is VOC-free, low hazard, and odourless.

How should I clean the application equipment?

Clean brushes and sprayers with water immediately after use.

Does it change the appearance of the surface?

No, it is designed not to change the aesthetic appearance of the building.

Troubleshooting

Water is still penetrating the surface.

Ensure the surface was properly cleaned and prepared before application. Reapply a second coat, making sure the entire surface is covered.

White residue appears on the surface after application.

This could be due to over-application or applying in direct sunlight. Ensure proper application rates and avoid applying in direct sunlight. If the residue persists, gently wash with water.

Uneven application or patchy appearance.

Ensure even coverage with each coat. Use a consistent spray pattern or brush strokes. Avoid applying too much product in one area.

Pros and Cons

Pros

Prevents water ingress, reducing the risk of water damage.
Allows walls to breathe, preventing moisture buildup.
Protects against frost damage, extending the lifespan of masonry.
Easy to apply using a low-pressure spray or brush.
Environmentally friendly due to its VOC-free composition.
Enhances the longevity and appearance of treated surfaces.

Cons

Requires thorough surface preparation for optimal results.
Two coats are needed for full protection, increasing application time.
Care must be taken to avoid overspray on surrounding surfaces.
Protection may be compromised if applied during rain.
Performance can vary depending on the porosity of the material.

Setup, Compatibility & Care

Preparation:

Ensure all surfaces are clean and free from dirt, mosses, and lichens.
Use Bond It MOULD STOP! to remove stubborn green growth or lichens. Allow a minimum of 24 hours for fresh pointing to dry before application.

Application:

Shake the bottle well before use.
Apply using a low-pressure spray (non-atomizing) or a brush.
Apply at a rate of 3m² per litre for porous stone and 5m² per litre for hard brick.
Apply with a smooth action, starting at the top and working down, ensuring full surface wetting.
Apply two coats, with the second coat applied while the first is still wet/tacky.

Care:

Avoid splashing or misting on cars, windows, painted surfaces, plants, and ponds.
Protect the surface if it starts to rain during application until fully cured.