Warren Reed Colorspray Splashback and Sealant Adhesive - Yellow
Not Available
Not Available
Not Available
Currently unavailable
Currently out of stock
This product is not available at the moment. Check back later.
Product Information
Full details
This guide is for DIY enthusiasts and professional installers looking to securely bond painted glass splashbacks and decorative panels. The Warren Reed Colorspray Adhesive offers a clear, neutral-curing solution that enhances artistic decor with its vibrant yellow hue, acting as both an adhesive and sealant. A key benefit is its solvent-free, fungicide-enhanced formula for mildew resistance, though users should note it's specifically designed for splashbacks and decorative panels, not general construction.
All features
| Colour | Yellow |
|---|---|
| Brand | Warren Reed - Designer |
Extended Product Information
FAQs
Can this adhesive be used on any type of glass?
Yes, it is suitable for painted glass splashbacks and general glass bonding applications where a clear, flexible seal is needed. Always ensure the glass surface is clean and dry before application.
What is the shelf life of the adhesive?
Unopened cartridges typically have a shelf life of 12 months when stored in a cool, dry place away from direct sunlight. Refer to the packaging for specific expiration dates.
Is this adhesive suitable for outdoor use?
This product is designed for interior applications. While it has good UV resistance and weatherability, it is not intended for permanent outdoor structural bonding.
How long does it take to fully cure?
Full cure typically takes 24 to 48 hours, depending on temperature, humidity, and the thickness of the bead. It skins over in about 15-20 minutes.
Can I paint over the cured sealant?
No, this product is not designed to be painted over. It is intended to provide a clear, finished edge or bond.
What is the difference between adhesive and sealant functions?
As an adhesive, it bonds two surfaces together. As a sealant, it fills gaps and prevents the passage of fluids or air, typically applied along joints and edges.
Does the yellow color family affect its performance?
The yellow color family is an aesthetic choice and does not impact the adhesive or sealant performance. The formula is clear and neutral curing.
Troubleshooting
Adhesive not bonding properly
Ensure surfaces are clean, dry, and free from dust or grease. Re-apply adhesive after thoroughly cleaning the surfaces. Ensure adequate pressure is applied during bonding.
Slow curing time
Curing is dependent on temperature and humidity. Ensure the application environment is within the recommended temperature range (typically 5°C to 30°C) and there is sufficient air circulation. High humidity can sometimes slow down the initial set but aids full cure.
Adhesive oozing from edges
Too much adhesive may have been applied. Carefully trim excess uncured adhesive with a sharp knife. For a neat seal, ensure a consistent bead is applied and tooled off correctly.
Mildew appearing on sealant
While fungicide enhanced, extreme conditions may still promote growth. Clean the area with a mild detergent and water. Ensure good ventilation in the area.
Pros and Cons
Pros
- Excellent adhesion for glass splashbacks and decorative panels.
- Fungicide additive provides good mildew resistance.
- Solvent-free formulation for safer handling and reduced environmental impact.
- Clear, neutral cure is aesthetically pleasing and non-corrosive.
- Dual function as both an adhesive and a sealant.
Cons
- Primarily designed for splashbacks and panels, may not be suitable for general construction bonding.
- Curing time can vary based on temperature and humidity.
- Requires proper surface preparation for optimal adhesion.
- Specific to the yellow color family; not a universal color match if renovation requires a different tone.
Setup, Compatibility & Care
Setup:
- Surface Preparation: Ensure all surfaces to be bonded are clean, dry, and free from dust, oil, grease, and any loose material. For non-porous surfaces, wiping with a suitable solvent cleaner and allowing to dry is recommended. For porous surfaces, ensure they are sound and not powdery.
- Application: Apply the adhesive using a caulking gun in beads or dots to one of the surfaces. For splashbacks, apply to the back of the glass. For sealing, apply a continuous bead along the joint.
- Bonding: Immediately position the splashback or panel into place. Apply firm, even pressure to ensure good contact. For edge sealing, smooth the bead with a wet finger or tooling knife.
- Curing: Allow adequate time for the adhesive to cure fully before exposing it to heavy use or moisture. Curing time will vary based on temperature and humidity (typically 24-48 hours for full cure).
Compatibility:
- Substrates: Compatible with glass, painted surfaces, ceramics, aluminum, wood, concrete, and many plastics. Always test on a small, inconspicuous area if unsure.
- Painted Glass: Specifically designed for use with painted glass splashbacks.
- Not Recommended For: Continuous water immersion, structural bonding, or use on substrates that may bleed oils or plasticizers.
Care:
- Cleaning Tools: Clean up excess uncured adhesive immediately with a damp cloth or appropriate solvent. Once cured, adhesive can be removed mechanically.
- Maintenance: The cured adhesive and sealant are durable. Clean the bonded area with mild soap and water. Avoid abrasive cleaners that could scratch the surface.