Shopping.co.uk

Timco Shield Anchor Projecting Bolt - M10 - 60P

Timco Shield Anchor Projecting Bolt - M10 - 60P

The Timco Shield Anchor Projecting Bolt is a traditional metal expansion anchor designed for relia...

Best current price£2.24from Power Tools Direct

Best offers

Shopping.co.uk recommended and popular offers

Lowest priceMost popular
Power Tools Direct£2.24Visit shop

Timco Yellow 1060Pshp Shield Anchor Projecting Bolts - M10:60p (M10 X 130) Timpac 2

Visit shop

All Offers

6 offers from £2.24 - £9.75

View price history by clicking the chart icon.

Power Tools DirectTimco Yellow 1060Pshp Shield Anchor Projecting Bolts - M10:60p (M10 X 130) Timpac 2
£5.95 delivery
£2.24
Visit shop
OnBuy.comTimco 1060Pshp Shield Anchor Projecting M10 / 60P Bag Of 2 5055331828736
Free delivery in 1–3 days
£5.90
Visit shop
eBayTIMCO - Shield Anchor Projecting Bolts - Yellow M10:60P (M10 x 130) [2PCS]
Free delivery in 1–3 days
£7.21
Visit shop
B&QB&Q - Shield Anchors Projecting Bolt GoldM10:60P (M10 X 130)
Free delivery in 1–3 days
£9.75
Visit shop

Product Information

Full details

The Timco Shield Anchor Projecting Bolt is an essential heavy-duty fixing solution for professionals and DIY enthusiasts working with masonry or concrete. Its primary benefit lies in the projecting stud design, which simplifies the alignment process by allowing users to position the fixture over the bolt before tightening, ensuring precise installation. While highly effective for structural and load-bearing applications, users should note that it requires a pre-drilled hole of specific dimensions to ensure the expansion mechanism engages correctly within the substrate.

All features

ColourYellow
Model Part Number1060PSHP
BrandTimco

Extended Product Information

FAQs

Can I use this in hollow brick?

No, this anchor is designed for solid masonry and concrete. It will not expand correctly in hollow materials.

What size hole should I drill?

Always match the drill bit diameter to the diameter of the shield anchor body.

Is this anchor reusable?

These anchors are intended for permanent installation; removing them usually damages the substrate.

Does it come with a nut and washer?

Yes, the Timco Shield Anchor Projecting Bolt comes as a complete assembly with the necessary nut and washer.

Can this be used outdoors?

While durable, it is recommended to ensure the installation area is not subject to extreme corrosive conditions without proper protection.

Troubleshooting

The anchor spins in the hole without tightening

The drill hole is likely too large or the masonry is too soft. Use the correct bit size or relocate the fixing point.

Nut cannot be fully tightened

Check that the hole is deep enough to accommodate the full length of the anchor and clear any trapped masonry dust from the base of the hole.

Pros and Cons

Pros

  • Simplifies fixture alignment due to the projecting stud
  • Provides high pull-out resistance in solid masonry
  • Easy to install with standard manual tools
  • Suitable for demanding construction environments

Cons

  • Not suitable for use in hollow blocks or fragile substrates
  • Requires precise drilling to avoid over-sizing the hole
  • The bolt remains exposed after installation

Setup, Compatibility & Care

  1. Drilling: Use a masonry drill bit of the correct diameter as specified by the anchor requirements. Ensure the hole is drilled to the recommended depth.
  2. Cleaning: Use a blower or wire brush to remove masonry dust from the hole; excess dust can reduce the expansion effectiveness.
  3. Insertion: Insert the shield anchor until the threaded stud is at the desired projection level.
  4. Tightening: Place the fixture, washer, and nut onto the stud, then tighten the nut to the recommended torque. Do not over-tighten, as this may damage the substrate.
  5. Care: Avoid exposure to corrosive chemicals that could degrade the metal over time. In exterior applications, ensure the connection point is protected from prolonged standing water.

Price History

DatePrice
Visit shop