This website uses cookies to improve user experience. By using our website you consent to all cookies in accordance with our Cookie Policy. Read more
Hi-Cap Half Round Union Bracket - FloPlast
Our range of High Capacity guttering has been designed to drain even the largest roofing areas eff...Our range of High Capacity guttering has been designed to drain even the largest roofing areas efficiently. The deep profile can accommodate a larger capacity of rainwater, ideal for buildings with large or steep roofs. The higher flow rate and deep capacity enable the amount of downpipes to be kept to a minimum. Deepflow Gutter Unions, sometimes referred to as joiners, are used to connect two lengths of deepflow gutter together in a run.Gutter is clipped in place using the same method was when installing all gutter fittings - the back edge first, then pull the front edge gently down into position until the clip snaps into place. Inside the gutter union are insertion marks, which show exactly where the gutter should be positioned. Aligning the gutter to these marks ensures that as the gutter expands and contracts with changes in temperature, the seal still makes full contact with the gutter.The waterproof seal is achieved by the downward pressure of the clips compressing the small rubber seal evenly around the outside of the gutter.Unions are fixed back to the fascia board using two countersunk screws.You can see our short PBSL Group video review of a gutter union below;
This guide is for homeowners and contractors using the FloPlast Hi-Cap Half Round Union Bracket. This bracket efficiently connects sections of Hi-Cap guttering, ensuring a watertight seal and optimal rainwater drainage. A key consideration is proper alignment during installation to maintain the seal's integrity over time.
All features
Brand
FloPlast
Extended Product Information
FAQs
What tools do I need for installation?
You will need a screwdriver, measuring tape, and possibly a ladder for installation.
How do I ensure a watertight seal?
Align the gutter sections with the insertion marks inside the union and ensure the clips are fully engaged.
Can I use this with other brands of guttering?
No, this union is specifically designed for FloPlast Hi-Cap Half Round guttering.
How do I clean the gutter union?
The union itself does not require regular cleaning. Focus on keeping the gutters clear of debris.
How often should I inspect the guttering system?
Inspect the guttering system at least twice a year, and after any severe weather events.
What is the purpose of the insertion marks?
The insertion marks ensure the correct alignment of the gutter sections, allowing for expansion and contraction with temperature changes without compromising the seal.
Where can I find a video of how to install this bracket?
A short PBSL Group video review of a gutter union is available online.
Troubleshooting
Gutter sections are leaking at the union.
Check the alignment of the gutter sections with the insertion marks. Ensure the clips are securely fastened, and the rubber seal is making full contact. Consider replacing the union if the seal is damaged.
The gutter union is loose.
Tighten the screws securing the union to the fascia board. Ensure the gutter is properly clipped into the union. If necessary, replace the union.
Pros and Cons
Pros
Efficiently connects Hi-Cap guttering sections.
Provides a watertight seal, preventing leaks.
Designed for high-capacity rainwater drainage.
Reduces the need for multiple downpipes.
Easy and straightforward installation process.
Cons
Requires precise alignment during installation.
May require additional screws for secure fixing.
Compatibility is limited to FloPlast Hi-Cap guttering systems only.
Seal performance can degrade over time if not properly installed or maintained.
Setup, Compatibility & Care
Compatibility: This union bracket is specifically designed for use with FloPlast Hi-Cap Half Round guttering systems.
Installation:
Align the gutter sections with the insertion marks inside the union.
Clip the gutter in place by inserting the back edge first, then pulling the front edge down until it snaps.
Use countersunk screws to fix the union to the fascia board.
Care: Regularly inspect the guttering system, including the union brackets. Clean the gutters of debris to maintain optimal water flow. Check the seal for any signs of wear or damage. Ensure that the clips are secure and the bracket is firmly attached to the fascia board.