Plumbsure Solder Ring Stop End - 28mm
Best current price£3.79from B&Q
Best offers
Shopping.co.uk recommended and popular offers
B&Q£3.79Visit shop - Copper Solder Ring Stop End (Dia)28mm
Visit shopB&Q£3.79Visit shop One Offer
1 offer from £3.79
View price history by clicking the chart icon.
Product Information
Full details
The Plumbsure Solder Ring Stop End is for DIY enthusiasts and professional plumbers seeking a reliable and cost-effective method for terminating copper pipework. Its key benefit is the integrated lead-free solder ring, which simplifies the jointing process by releasing solder upon heating, ensuring a secure connection with minimal effort. A caveat to be aware of is the necessary preparation of copper pipes with a pipe cleaner and flux before soldering.
All features
| Brand | B&Q |
|---|
Extended Product Information
FAQs
What is a solder ring stop end fitting?
A solder ring stop end fitting is a plumbing component used to terminate a copper pipe run. It features a built-in ring of solder that melts when heated with a blow torch, creating a secure and watertight seal.
What size copper pipe does this fitting work with?
This Plumbsure Solder Ring Stop End fitting is designed for 28mm diameter copper piping.
Do I need to use flux with this fitting?
Yes, even though the fitting has a pre-fitted solder ring, the copper pipe must be cleaned and treated with flux before assembly to ensure a proper solder flow and a strong joint.
What type of blow torch should I use?
A standard propane or MAPP gas blow torch is suitable for heating the fitting and melting the integrated solder ring.
Is the solder lead-free?
Yes, the product description specifies that the integrated solder ring is made of high-quality, lead-free solder.
Can this fitting be used for gas lines?
This fitting is designed for water plumbing systems. For gas lines, specific gas-rated fittings and procedures must be followed.
How long will it take to heat the fitting?
Heating time varies depending on the blow torch power and ambient conditions, but typically takes 30-60 seconds of steady heating to melt the solder. Aim for even heating of the entire fitting.
Troubleshooting
Joint is leaking after soldering
The pipe may not have been heated sufficiently, or the solder did not fully flow. Ensure even heating of the fitting and pipe. Reheat the joint and allow more time for the solder to flow. Ensure pipe preparation (cleaning and flux) was adequate.
Solder did not melt or flow properly
Check that the blow torch is producing a strong enough flame and is being applied correctly. Ensure the fitting is heated evenly around its circumference. Verify that the correct type of flux was used and applied correctly.
Fitting is difficult to slide onto the pipe
The pipe may have burrs or is not perfectly round. Ensure the pipe end is clean, smooth, and deburred. Re-clean the pipe end if necessary.
Pros and Cons
Pros
- Simplifies pipe jointing with pre-fitted solder.
- Cost-effective plumbing solution.
- Durable and reliable for secure connections.
- Lead-free solder ensures a safer joint.
Cons
- Requires a blow torch for installation.
- Copper pipe preparation (cleaning and fluxing) is essential.
- Not suitable for non-standard pipe sizes.
Setup, Compatibility & Care
Setup:
- Ensure the 28mm copper pipe end is clean and free of any debris or oxidation. Use a pipe cleaner or abrasive pad.
- Apply a thin, even layer of appropriate flux to the outside of the copper pipe end and the inside of the fitting.
- Slide the Plumbsure Solder Ring Stop End fitting onto the prepared copper pipe.
- Using a propane or MAPP gas blow torch, heat the fitting evenly, paying attention to the area where the pipe enters the fitting and where the solder ring is located.
- As the fitting reaches the correct temperature, the pre-fitted solder ring will melt and flow into the gap between the pipe and the fitting, creating a strong, sealed joint.
- Allow the joint to cool undisturbed.
Compatibility:
- This fitting is specifically designed for use with 28mm copper piping.
- Requires a compatible blow torch and fuel source (e.g., propane, MAPP gas).
- Use with appropriate plumbing flux and pipe cleaning materials.
Care:
- Store in a dry place to prevent corrosion of the copper and contamination of the solder ring.
- Handle with care to avoid damaging the integrated solder ring before installation.
- After installation, the joint requires no special care beyond standard plumbing system maintenance.