Best current price£24.91from B&Q
Shopping.co.uk recommended and popular offers
B&Q£24.91Visit shop B&Q - J-B Weld Clear Yellow Plasticweld Quick-Setting Epoxy (2 Pack)25Ml Syringes5-Minute Set TimeStrong Plastic Bond
Visit shop2 offers from £24.91 - £25.38
View price history by clicking the chart icon.
The JB Weld Clear Yellow PlasticWeld is designed for individuals needing to quickly and effectively repair plastic components and bond mixed materials. Its primary benefit is the rapid 5-minute set time, allowing for swift project completion. A potential caveat is its specific formulation for plastics, which may require surface preparation for optimal adhesion on non-plastic materials. This two-part epoxy features a dual-syringe for precise mixing, ensuring a strong, impact-resistant bond ideal for automotive, household, and DIY repairs.
| Colour | Yellow |
|---|---|
| Model Part Number | Plasticweld |
| Brand | JB Weld |
The working time is very short due to the 5-minute set time. It is recommended to mix only what you can use immediately, typically within 1-2 minutes.
The epoxy cures to a clear yellow color. While it can bond clear plastics, the cured color may be noticeable. For invisible repairs on perfectly clear items, another product might be more suitable.
Wipe away uncured epoxy immediately with a damp cloth. For stubborn residue or cured epoxy, mechanical removal (sanding) may be necessary.
The ideal application temperature range is between 50°F and 90°F (10°C and 32°C). Colder temperatures will slow down the curing process.
Yes, once fully cured, the epoxy can be sanded, drilled, tapped, and painted.
Yes, the cured epoxy forms a water-resistant bond, making it suitable for repairs that may be exposed to moisture.
Avoid using on polyethylene, polypropylene, Teflon, or silicone-type plastics as they are difficult to bond effectively.
Ensure equal amounts of resin and hardener were dispensed and mixed thoroughly. Check that the ambient temperature is within the recommended range (typically 50°F to 90°F / 10°C to 32°C). If conditions are too cold, curing will be significantly slower.
The surface may not have been properly prepared. Clean the surfaces thoroughly to remove all dirt, grease, oil, or old adhesive. Lightly abrade the surface with sandpaper to create a better mechanical bond.
Ensure the plunger is fully seated before attempting to dispense. If the epoxy has begun to cure inside the tip, carefully try to clear it or use a new syringe if the pack allows. Store syringes upright with tips sealed.
The application may have exceeded the product's limitations, such as exposure to extreme heat, chemical solvents, or excessive stress. For higher-stress or heat applications, consider a different J-B Weld product.
Setup: To use J-B Weld PlasticWeld, ensure both surfaces to be bonded are clean, dry, and free from grease or dirt. Lightly roughening the surfaces with sandpaper can improve adhesion. Dispense equal amounts of resin and hardener from the dual-syringe onto a clean, disposable mixing surface. Mix thoroughly until a uniform color is achieved. Apply the mixed epoxy to one surface, bring the parts together, and hold them in place for the 5-minute set time. Full cure is typically achieved within 1-2 hours, though strength increases over 24 hours.
Compatibility: This epoxy is specially formulated for a wide array of plastics, including polystyrene, ABS, PVC, fiberglass, and more. It also adheres well to metal, ceramic, glass, wood, and concrete. Avoid use on polyethylene, polypropylene, Teflon, or silicone-type plastics, as they are difficult to bond.
Care: Store unused syringes in a cool, dry place away from direct sunlight. Ensure the caps are tightly sealed to prevent premature curing. Clean up any uncured excess epoxy immediately with a damp cloth. Once cured, the epoxy is permanent and can be sanded, drilled, and painted.
